How to unlock Shangai Even Boost M028T- ( L02C BOARD )

STEPS:

         

 Donate For More Free Tutorials


Video Link: https://youtu.be/cGZgosealUM

1.Download the unlock files

Link:http: http://linkshrink.net/7DkPvH

2.Install WTPTP Driver

Note: Install this driver base on your system type (x86 and x64 bit)

3. Install Generic Mifi Drivers manually using the link below

https://icdi-tech.info/2013/09/07/installing-generic-mifi-drivers-manually/

4. You are now ready to unlock your device.



NOTE: During the First Flash, you have to disconnect the MiFi at 20% To 24% Erase All Flash To allow the device to accept different incompatible loaders.



FLASHING THE FIRST FILE(Uganda Firmware)

i.  Open L02BUganda1_M023_LCD_V003 firmware in your extracted files.

ii.  Open/Run SWDownloader.exe file.

iii. Click on the small folder icon and select the blf file ( Nezha_MiFi5_LWG_Only_Nontrusted )

watch the pictures below

iv. Click on Options and Select Erase All Flash
v. Tick other non Ticked files.

vi.  Proceed to Start by clicking on the Green Button and Connect the device without battery to start flashing.

NOTE: During the First Flash, you have to disconnect the MiFi at 20% To 24% Erase All Flash by Removing the Usb cable from the Device.


FLASHING THE SECOND FILE.   ( Last Flash )
                                                        { L02C_M028T_VodafoneCameroon }



NOTE:Do not interrupt the flash this time
Follow the exact instructions in the pictures below
i. Open software, Open SWD folder and select Nehza ( blf ) file to load flash files
ii. Tick other non ticked files.
iii. Select Erase all flashed in Options 
iv. Proceed to Start by clicking on the Green Button and Connect the device without battery to flash.
                                                                                   ( Do not interrupt the flash this time )

v.Disconnect the Device. 

( The Device Is Now Unlocked )



                                                                                     CONFIGURING THE DEVICE
1.  Change the default SIM card with any network provider SIM.

2.  Power the Device ON.   The Device will Ask For PH-NET PIN)

                                   (The Unlock code is 123456)

                                              
3. Connect the Device to the PC using the USB cable or WiFi.
4. Open your web browser and navigate to 192.168.1.1
5. You will be asked to enter username and password. Enter “smartbro” as username and password.
 6. Skip the Welcome page, Click on the Internet TAB
 7. Select MEP Settings and Type the Unlock Code As 123456 and Click On Unlock.
8. Goto Internet TAB and Change the Preferred Network Mode to 4G-HSPA+/3G
9.Locate Auto Configure APN at the Bottom of the Internet TAB page and Untick  Auto Configure APN, 
Save your settings.
                                       Follow the exact instructions in the pictures below


1. Login to the Dashboard 192.168.1.1  and Type “smartbro” as Username and Password

2. Skip the Welcome page, Click on the Internet TAB,

Select MEP Settings and Type the Unlock Code As 123456

3. Unlock Code accepted; you should see Searching for Signals on your MiFi, Just wait for the Device to display your Sim Network.

4. Locate Auto Configure APN at the Bottom of the Internet TAB page and Untick  Auto Configure APN,
Save your settings.

NOTE:You will see PH-NET PIN each time you reset your Device.  The Unlock code is 123456.


         

 Donate For More Free Tutorials



2 Comments

  1. spidersu8090

    please gave me a firmware of L02C_M028T_VodafoneCameroon

Leave a Reply

Your email address will not be published.